Benchmate Package

BenchMate is a powerful holding system that stabilizes stone setting, speeds up soldering and simplifies jewelry repair. BenchMate reduces the hand force needed to set stones.

You can set more stones per day and do a nicer job with less strain and greater confidence.
Special attachments turn BenchMate into an advanced soldering aid. You'll finish jobs like prong retipping, shank repair and ring sizing, faster.

BenchMate simplifies complex jewelry fabrication and torch work, making you a better jeweler. Using BenchMate requires no major change to your work methods. Just fasten the tapered Fixed Mounting Plate on the front of your bench.

This plate mates with every BenchMate attachment including: Basic BenchMate Holder, Bench Pin, Engraving Vise Shelf, Sawing Plate, BenchMate Vise, Double Soldering Station. To change attachments, you lift them up and off the tapered Fixed Mounting Plate.

It takes three seconds and requires no tools. This patented system keeps your work centered in front of your bench at the right height. You'll maintain good body posture for greater comfort throughout the day.

The Basic BenchMate Holder tilts and rotates to any position while you work on rings, pendants, earrings, and other jewelry. Its jaws hold both jewelry and other attachments including: Narrow Solder Fingers, Wide Solder Fingers, Shellac Pads, Pitch Cup, and 4" (100mm) Solder Station.

The holder moves freely in all directions, or you can add selective resistance by tightening the pivot knobs.

You can also lock it solidly in any position. The BenchMate Holder moves only when and where you want. This eliminates accidental slips that can ruin your work or injure you.

• INCLUDES
• BenchmateTM
• Shellac Pad
• Both Soldering Clamps
• (2)Third Hand Attachment
• Soldering Pad Assembly
• Bench Pin Kit
• Fixed Mounting Plate
• Mounting Hardware

Cleaning a Jewelry

You have lots of jewelries and it was on your jewelry box do you have time to clean it?

In cleaning a jewelry you need to scrub or polish it but how can you clean jewelry without ruining its quality? How can you remove those dirt’s and grime?

Before you start cleaning your jewelry you need to make sure that the jewelry are secured and well fastened to avoid loosing a piece of it. You also need different cleaning cloth that will match the quality of your jewelries. Cleaning a gold jewelry is very different in cleaning your silver jewelry.  There are some cleaning chemicals that might damage your jewelries and it is very important to start cleaning your jewelries in a gentle manner.

Nowadays, because of technology you can now clean your jewelries in just a couple of minutes. How? By using a sparkle spa ultrasonic it has a power of a professional jewelry cleaner that is quick and easy top use. You can also use distilled water or a cleaning solutions. The ultrasonic device will be the one who will going to remove the dirt and grime and also the tarnishing of jewelry.

For more information about the tools in cleaning your jewelries you can visit Rosenthal Jewelers Supply where you can buy wholesale jewelry tools and supplies at a very low price.

Jewelers Toy Store: Laser Welding Tips and Techniques

Frank McAllister, CEO of a well known Mining company studied the quantity of a jewelry that was made from 950 palladium has surpassed the same for platinum products. He calculated the number of ounces that was used globally for each alloy.

If you will going to use a laser welding to the 950 palladium you need to make sure that it was setup properly. Laser welding's equipment settings and technical procedure might differ to platinum. The three most requested bench tasks that was used for a successful laser welding of 950 palladium products are:

1. Filling voids and pits

2. Minor assembly

3. Ring sizing

Research was conducted to do some testing for them to be able to use the laser welding perfectly specially for a 950 palladium. It is very important that the settings of the laser machine are correct and equipment should be maintain properly to avoid any bad effect for the final outcome. For us to explain clearly, we will going to explain how those bench tasks works.

Filling Voids and Pits

During the casting process with jewelries alloy most often result to voids and pits. By using laser welding you can hit the void several times to open and shape it. The tip of the wire was held in direct contact with the palladium piece, within the void and a pulse of energy melted 950 palladium from the wire into the void. Each void was overfilled with 950 palladium and then filed even with the surface of the ring for finishing. Make sure that when filling voids and pits using a laser you should start by directly to the void. On this way, it will melt the bottom and will expose fresh metal from which to build upon.

Minor Assembly

For minor assembly the most effective way is to tack the parts using a laser welder followed by soldering to complete the process.

Ring Sizing

It is not always safe to resize a palladium using a torch because gemstones are heat sensitive. Because of that we need to set the equipment properly to avoid the metal become brittle.

Experts continuously do some research about the best options for using a laser welder. But, as of now it is much easier to follow those procedures to avoid breaking the metals that you have.

Laser Welder For Sale

Are you looking for a laser welder that is reliable and easy to use? Or, maybe you are looking for a company who can provide you a laser welder and can help you on how to use it?

“Buying a laser welder for us was quite a big step in separating ourselves from others in our town.  We can now offer the latest technology on the market.  Whenever we considered buying a laser welder we searched out several vendors.  But the choice for us was easy.  The machine that you sell is by far, in our opinion, the best laser welder on the market.  Other companies could not compare when it came down to the overall complete packages.  Rosenthal exceeded our expectations tremendously.”  From, Barnes Jewelers Inc.

Laser Welder works as a soldering machine, it can also be used for retipping and fixing jewelry cracks. It can fix any type of jewelry such as titanium, platinum, silver, steel, gold and many more.

Because we are going to use laser that means we are using the energy of light with a very thin light that can be used in a hard to reach areas of jewelry. Because we are using a light energy then that light energy will be converted into a thermal energy and became a concentrated energy. This concentrated energy will produce melting and coalescence on that way jewelry will be melted easily.

To purchase a laser welder you need to choose what’s best for your jewelry business. In Rosenthal, there are two types of laser welder that you can choose from. First one is the Desktop Laser Welder, this laser welder are for lightweight repairs. Because it is lightweight that means it is much easier to transport and to maintain. Another laser welder that we offer is a Bench Top Pro Laser BD-60, this can perform just like a larger sized welding machine. This machine was designed for the users who are looking for a machine with the ability of a larger machine but not that expensive.

In conclusion, if you are looking for a laser welder that is reliable and easy to use, Rosenthal Jewelers Supply can provide it to you. Aside from that, they can also train you on how to use it. Customers satisfaction is very important.

Metal Smithing

What does metal smithing means? What does a metal smithing do to create jewelries?

Metal smithing, just like black smith a metal smith is a person that involves creating object for example jewelry out of metal. Metal smithing is the process of creating the object out of metal.

To get started as a metal smith you need some tools that’s the first investment that you need.

Here are the tools that you needed to become a metal smith:

Bench Pin. It will allow the jewelry maker or metalsmith to have a good firm handle on any item of jewelry that is being made, repaired, designed or created Made of wood.

Saw frame. Made of steel with comfortable hardwood handles. Available in various sizes and qualities, will accommodate
all standard jewelers saw blades.

Set of pliers. A must for metal smithing, diamond and gem setting, Bead smithing, beadstrining, making jump rings, jewelry repairs, and more. These, Jewelers Pliers are made and designed for the jeweler in mind, comfort handle, economical, and well constructed allow the jeweler to use for hours, day after day with confidence in the performance.

Needle Files. Precision files for exacting work, especially under magnification. Made of the highest quality steel, machined and finished for precision shape, accuracy and balance.

Solder. Comes in sheet and wires. You also need soft, medium, and hard solder.

Brush. You can use a paint brush to apply flux.

Flux. Used to help the solders stick to the metal. You can use flux in paste form for easy application.

Those are some of the things that a metal smith needed to start creating jewelry out of metal. Those tools can be purchased at your local hardware or you can also visit Rosenthal Jewelers Supply website.

Handmade Jewelries

Creating your own jewelries is really a fun thing to do. To think that you will be creating your own jewelries with a personal touch. You can choose your own color, gemstone and you can also create your own design. Aside from that, you can even sell those jewelries to your friends.

There are some points to remember in creating your own jewelries.

·        You need to make sure that you have the best materials that are available in your area

·        Don’t even try to use a fishing line to create your jewelries

·        Use nylon coated string to start creating your jewelries

·        When you start creating your jewelries make sure it is not too tight to prevent from breaking. You also need to make sure its not too stiff

·        Make sure that you are creating the right size for the right jewelries. You can use a bead stringing board to get the precise size of the craft

·        Once you already finished creating your jewelries make sure you also take good care of it

Those are the tips that you can bear in mind in creating your own craft. If you follow those tips we can assure you that you will be creating the best craft that you’ve ever made.

Aside from that, you also need to know how to take good care of the craft that you created. Just like what the last points to remember.

Once you already created a craft you need to make sure not to wear it during sports time. You can also avoid using chemicals that might affect the materials that have been used. Instead of using chemicals you can just use a cleaning cloth to clean your jewelries. You can also remove your jewelries while cleaning the house and doing other household chores.

Once you are able to follow that we can assure you that your jewelries will last longer. And other people might think of getting one of it and might inform their friends about it. And that’s the start of your jewelry business.

Stone to Test Gold

There are lots of ways to test gold. Because gold is also one of the precious stones that we have we need to make sure that you are getting the value of your money.

We all know that a real gold is really expensive. You need to spend thousands of money just to get a small piece of gold. That is why lots of jewelers are using different ways to test gold.

Some of the jewelers use acid, electronic devices and some are using a special stone to test gold.

The stone that are being used to test gold is a dark stone. It is used to test the karat of gold as well as silver and even platinum.

How to use the gold test stone?

To use it you just need to rub the pieces of gold to the stone. If you see a yellow strike on the dark stone that means it is pure gold.

Some jewelers are also using magnet to test gold. They will hold a magnet near the stone and see if it will attract the gold. If it will that means there are other metals that are included on the said stone.

For more information on the tools to test gold, you can visit the website www.JewelersToyStore.com

Presidium Duo Tester

Identify Diamonds & Colored Stones!
The PRESIDIUM DUOTESTER is the only tool on the market that provides the user with two proven tests for diamonds and the ability to differentiate between similarly colored gemstones. The easy-to-read dial of the DUOTESTER is calibrated to indicate the differences in thermal conductivity of the most popular gemstones and simulants. Simply touch the tip of the thermal conductivity probe pen to a mounted or loose stone. Diamond is easily identified by any reading in the green area of the dial, and colored gemstones can be easily differentiated from one another by the clearly labeled zones provided in the red area. Even coated gemstones can be accurately tested.

DIGITAL REFLECTIVITY MEASUREMENT
Diamond and its simulants reflect light proportionally to their respective refractive index. The PRESIDIUM DUOTESTER provides the user with a digital reflectivity meter and an easy to use Simulant Reflectivity Chart. The reflectivity number from the meter is simply cross-referenced with the chart to identify the stone. An unknown gemstone can be tested for its thermal conductivity and, if necessary, the results can be confirmed with a quick and simple reflectivity test. All stones indicated as diamond by the thermal tester should be tested with the reflectivity meter to test for Synthetic Moissanite, thus providing double the assurance for the same price.

Easy Fail Safe Calibration
The PRESIDIUM DUOTESTER comes complete with built in diamond and simulant test discs for easy calibration of the thermal tester. Calibration of the Reflectivity Meter is made easy with the optional, built in diamond substitute set.

Convenience
The thermal probe pen includes a metal warning detector that emits a audible buzz if the gem mounting is accidentally touched. The DOUTESTER can be powered by 5 AA alkaline batteries or by the electrical adapter provided.

Guaranteed Quality
The PRESIDIUM DUOTESTER is manufactured under rigid quality standards. The user is assured of the highest satisfaction and dependable service from this PRESIDIUM instrument. Each DUOTESTER is tested for functionality before shipment.

All About Diamond Tester

Diamond is known as girls best friends.

A diamond is a transparent type of crystal that is mostly used in creating and accessorizing different jewelries. It is also known as the hardest type of stone. Because it is the hardest it can even cut glasses and also this is the only stone that can scratch other gemstones.

Because diamonds is one of the well known stones and one of the precious stones that we have all over the world. That is the reason why some people or jewelers are creating a stone like jewelries but are not real. That is why a tester is created or invented.

Presidium diamondmate are created to utilize proven thermal conductivity testing method to instantly verify the authenticity of diamonds,

Because it was created to test diamond it will also provide you indication whether a diamond is real or not. It has a light indicator that indicates the quality of the diamonds.

For more information about the said product, you can visit the website at www.JewelersToyStore.com

Desktop Laser Welding

Laser welding is one of the most popular tools that can be used in creating different types of jewelries. Aside from that it can also be used in fixing, welding, soldering a jewelry.

Currently, JewelersToyStore is offering BD 60 Pro Micro Laser is the most cost effective laser available. It can out perform many other larger sized welders and it's small size allows it to be used in any facility. For use on gold, Platinum, silver, titanium, and steel alloys. The BD 60 Pro is designed for users that want the abilities of a larger machine but, are excluded by the cost. Application: For retail repair shops Jewelry design and repair, watch and eye glasses, medical technology material deposit, and repair of small molds and inserts.

For more information about the said tools, you can visit www.JewelersToyStore.com

Abrasive Paper

There are different types of abrasive paper:

·        3m Platinum

·        Emery

·        Water Proof

·        3m Wet/Dry

·        Metalite cloth

3M Platinum abrasive are uniquely designed for platinum jewelries.

Emery Paper is used for smooth and glossy finish. For you to be able to achieve the smoothest finish you can use the high quality emery in which grains are bonded on flexible paper. It is also designed to remove scratches, dry polishing, or lapping gold, silver, brass and copper. Also used for light deburring and cleaning heavy stock.

Waterproof paper abrasives was used for more aggressive waterproof paper sheet sanding applications, jewelers use Durite Waterproof Paper.  Packed in protective dispensers to eliminate waste and permit easy, neat storage. Typical applications include intermediate and final sanding of jewelry. These sheets have Aluminum oxide grain electro-coated on flexible cloth backing. Out performs emery. Leaves a smooth even finish.

3M wet or Dry Polishing Paper provides excellent flexibility for finishing and polishing plastics, metal and coatings. Used by jewelers, these polishing papers are pliable, non-woven, lint free backing, coated with micron graded aluminum oxide and silicone carbide particles slurry coated onto a non-woven synthetic backing, the superior flexibility of this product allows for fast and easy finishing and polishing on to almost all contoured surfaces.

Metalite Cloth is ideal for general metal sanding, scouring, deburring, and removing rust. Aluminum oxide grain is close-coated on cloth backing for aggressive cutting action, long life and fine finishes. These sheets out performs emery and is used extensively for polishing, deburring of jewelry made of gold, silver, platinum and other metals.

For more information about the product, you can visit our website at www.JewelersToyStore.com

Platinum Casting Machine

Platinum casting machine is a top quality heavy duty aluminum cast construction and stainless steel arm at a great value price. This platinum vertical centrifugal machine is your one stop solution for platinum casting.

According to jewelers, it is much harder to cast platinum than other metals. That is why they come up with a machine for casting platinum. Their goal is to get a good quality every time they cast platinum and any other metal.

This machine has a step by step procedure on how to use it and how to take care of it.

For more information about the Platinum casting machine, you can visit our website at www.JewelersToyStore.com

KAYA Casting Vacuum Machine

KAYA Casting Vacuum machine is a high quality machine that was designed to outperform and outlast any comparable unit in the industry.

KAYA Casting Vacuum Machine includes:

·        A crucible handle

·        Flask sleeve

·        Bell jar

·        Sprue base

·        Vacuum pump oil

·        Perforated flask

For more information about the KAYA Machine, please visit our website at www.JewelersToyStore.com

DAZOR CIRCULINE LAMP MAGNIFIER

Rosenthal Jewelers Supplies best selling product for magnifier which is what you called Dazor Circuline Lamp Magnifier. It has been used by professional jewelers, artists, architects, and quality control personnel for lots of years.

It is mostly used for jewelers because of the shadow free light while under the magnifying lens. The circular light source uniformly illuminates the viewing surface so that color contrasts are enhanced without competing shadows. The 5-inch diameter lens is precision ground, crown optical glass for near-zero light refraction and dispersion and is available with either a 3 or 5 diopter lens. This magnifiers is mounted on Dazor's contemporary "Floating-arm" that lets you position the light source and lens with the touch of a finger. The rugged steel construction is designed to provide years of service.

For more information about the product, please visit our website at www.jewelerstoystore.com

X-Ray Precious Metal Tester

This metal tester is based on an X-ray fluorescence analysis technology. It is the best technology and instrument for metal and jewelry analysis. It has a non-destructive, accurate and fast character.

X-RAY can analyze all kinds of precious metal jewelry, include gold, platinum, white gold, K gold, silver, and so on. The installation and operation of X-RAY are very easy, and the operator doesn't need any special training. All operation can consult Operation Manual, and can be finished by keyboard or mouse key.

X-RAY Precious Metal Tester is faster than previous model, so it spends short time in operating. It only takes several seconds for qualitative analysis and 3 minutes for quantitative analysis.

For more information about the product, please visit our website at www.jewelerstoystore.com

Gemoro 2QT Ultrasonic Heaters

Gemoro 2 Quart Ultrasonic Heater is a proprietary of super high performance industrial transducer. It has a heavy duty stainless steel and a long life built in switch guard boot cover.

External fuse for easy access & special internal fuse for ultimate protection. Stainless steel lids are standard with all models & help reduce evaporation. It also illuminated heater & turbo switch.

 For more information about the product, please visit our website at www.jewelerstoystore.com

Computerized Jewelry Engraving System

As one of the well known jewelers suppliers Rosenthal Jewelry Supply offer one of the best tools to be used in creating or designing your jewelries.

A jewelry engraving system that was created with a well known technology nowadays which is the computer.

Computerized jewelry engraving system can engraves both flat and curved surfaces, inside and outside the jewelry. It can easily replaced diamond tip.

This tool has complete accessories to be used in different type of jewelry job. It has vises, clamps and jogs to hold the jewelries in place.

In Rosenthal Jewelry Supply’s engraving system it also includes easy to install operating system, different style of fonts and a laser feature that can make the job easier.

For more information, please visit our website at www.jewelerstoystore.com